Holiday Shipping Notice: Orders placed after Nov. 24th will not be processed until Nov. 30th.


A Dealer’s Dosing Reference—The Three Kinds of Shock and What Each Is For, Label Doses by Spa Size for FreshWater® and Leisure Time® Products, the Liquid-Chlorine Math, When to Shock and How Long to Wait, Why a Salt-System Spa Should Boost Instead, and the Cyanuric-Acid Rule That Keeps Dichlor From Locking Up Your Water


Hot tub shock doses, from the product labels: dichlor chlorinating granules (FreshWater® Chlorine Granules or Leisure Time® Spa 56) shock at 1 oz per 500 gallons—about 2 tablespoons—which is double the ½-oz routine dose; non-chlorine MPS shock (FreshWater MPS Chlorine-Free Oxidizer or Leisure Time Renew) doses at 2 oz per 250 gallons; and liquid chlorine takes roughly ⅔ fl oz of 10–12% pool chlorine, or about 1 fl oz of plain 6% bleach, per 100 gallons to raise the water about 5 ppm. Add any of them with the jets on and the cover open, circulate 15–20 minutes, and don’t get in until free chlorine reads 5 ppm or less. On a FreshWater Salt System spa, use Boost (or MPS or liquid chlorine) rather than repeated dichlor, which builds cyanuric acid. Every product here ships nationwide from our online store.

“How much shock” has three honest answers, because there are three kinds of shock and they’re dosed differently. The labels tell you the rate, but not what the rate does, when to use which, or why the same scoop that fixes a chlorine spa can quietly ruin a salt spa over a season. This guide puts the label doses in one table by spa size, adds the chemistry behind them so you can adjust with a test strip instead of a guess, and gives both FreshWater and Leisure Time options for every situation.

The Three Kinds of Shock

Shock What It Is What It Does Trade-offs
Dichlor granules — FreshWater Chlorine Granules, Leisure Time Spa 56 Stabilized chlorine, about 56% available chlorine, pH-neutral, shelf-stable Oxidizes organics and raises the chlorine residual—the only shock that sanitizes too Every dose adds cyanuric acid (CYA), which never leaves the water; builds up with repeated use
MPS (non-chlorine shock) — FreshWater MPS Chlorine-Free Oxidizer, Leisure Time Renew Potassium peroxymonosulfate, an oxidizer with no chlorine Burns off oils, sweat, and chloramines; frees existing chlorine to work; soak again in about 15 minutes Adds no sanitizer residual, so it won’t fix low chlorine on its own; adds no CYA
Liquid chlorine — 10–12% pool chlorine or plain 5–6% household bleach Sodium hypochlorite, unstabilized Oxidizes and sanitizes with no CYA; Hot Spring’s recommended way to build a residual quickly on a salt spa pH about 11 (drives pH up), adds salt, short shelf life, easy to spill; never scented or splashless

Dosing by Gallons

Find your spa’s water capacity on its spec sheet or product page (a Hot Spring Grandee® and Envoy®, for example, hold 455 gallons). Doses below are from the product labels; the teaspoon and tablespoon equivalents are approximate—a kitchen scale or the scoop in the container is more accurate.

Dichlor: FreshWater Chlorine Granules or Leisure Time Spa 56

Label rate: ½ oz per 500 gallons for routine sanitizing (about a tablespoon), 1 oz per 500 gallons to shock. One ounce in 500 gallons raises free chlorine on the order of 8 ppm; a half-ounce, about 4.

Spa Capacity Routine Dose Shock Dose
200 gal 0.2 oz (about 1¼ tsp) 0.4 oz (about 2½ tsp)
250 gal ¼ oz (about 1½ tsp) ½ oz (about 1 tbsp)
300 gal 0.3 oz (about 2 tsp) 0.6 oz (about 1¼ tbsp)
350 gal 0.35 oz (about 2¼ tsp) 0.7 oz (about 1½ tbsp)
400 gal 0.4 oz (about 2½ tsp) 0.8 oz (about 1½ tbsp)
450 gal 0.45 oz (about 1 tbsp) 0.9 oz (about 1¾ tbsp)
500 gal ½ oz (about 1 tbsp) 1 oz (about 2 tbsp)
Option A: FreshWater Option B: Leisure Time Spa Care
FreshWater Concentrated Chlorinating Granules, 2 lb  •  3.5 lb Leisure Time Spa 56 Chlorinating Granules, 2 lb or 5 lb (same ½ oz per 500 gal routine rate; shock per label)

MPS Non-Chlorine Shock: FreshWater MPS or Leisure Time Renew

Label rate: 2 oz per 250 gallons, jets on, cover off, circulate 15 minutes. Both products are potassium peroxymonosulfate and dose identically. (For Leisure Time’s Reserve & Renew bromine-free program, Renew doubles to 4 oz per 250 gallons.)

Spa Capacity MPS / Renew Shock Dose
200 gal 1.6 oz (about 3 tbsp)
250 gal 2 oz (about ¼ cup)
300 gal 2.4 oz (about 5 tbsp)
350 gal 2.8 oz (about 5½ tbsp)
400 gal 3.2 oz (about 6½ tbsp)
450 gal 3.6 oz (about 7 tbsp)
500 gal 4 oz (about ½ cup)
Option A: FreshWater Option B: Leisure Time Spa Care
FreshWater MPS Chlorine-Free Oxidizer, 2.5 lb or 5 lb  •  FreshWater MPS Test Strips to read the residual (target 5–10 ppm) Leisure Time Renew, 2.2 lb  •  Renew, 5 lb

Liquid Chlorine: Pool Chlorine or Plain Bleach

No label rate exists for spas, so this is chemistry. To raise free chlorine by about 5 ppm: 10–12% pool chlorine, roughly ⅔ fl oz per 100 gallons; plain 6% household bleach, roughly 1 fl oz per 100 gallons. Measure, don’t pour, and retest after 5–15 minutes. Use only plain, unscented bleach—never splashless, scented, or “non-splash” products, which contain additives the water can’t clear.

Spa Capacity 10–12% Pool Chlorine (about 5 ppm) 6% Plain Bleach (about 5 ppm)
200 gal about 1¼ fl oz about 2 fl oz
300 gal about 2 fl oz about 3¼ fl oz
400 gal about 2½ fl oz about 4¼ fl oz
500 gal about 3¼ fl oz about 5½ fl oz
Dose to the Strip, Not the Spoon

Every number above is a starting point. Fill water, bather load, temperature, and how long since the last shock all change what a dose delivers, so the label rate gets you close and a 5-Way Test Strip finishes the job: dose, circulate, test after 5–15 minutes, and add a little more if you’re short of the target. That’s also why Hot Spring’s start-up instruction is “shock to achieve 5 ppm,” not “add X ounces”—the target is the number on the strip.

When to Shock, and How

  • Weekly, as routine maintenance, to burn off the week’s organics before they become chloramines.
  • After heavy use—a party, a crowd, a long soak. The Leisure Time program suggests a Renew shock after each use.
  • When the water tells you: cloudiness, a chlorine smell (that’s chloramines—see our smelly-water guide), foam, or combined chlorine over 0.5 ppm on the strip.
  • At start-up, after a fill: shock to 5 ppm once the water is balanced, and again daily until it holds 3 ppm on its own.

The method is the same for all three: jets on, cover off, add the dose to the water (never the filter compartment for dichlor—it can bleach the filter) with the water moving, circulate 15–20 minutes with the cover open so chloramines gas off instead of redissolving, then rinse the filter the next day. Test before you get in: free chlorine must be 5 ppm or less—typically 15–30 minutes after a standard dichlor shock, and about 15 minutes after MPS.

On a FreshWater Salt System: Boost, Don’t Bucket

A salt-system spa makes its own chlorine with no stabilizer, which is one of its quiet advantages—cyanuric acid never builds. Owners undo that by shocking with dichlor every time the reading dips. Hot Spring’s guidance is specific: it is “not recommended to add chlorine multiple times per week; system output and/or Boost mode should be used to maintain residual chlorine.” So on a salt spa:

  • For a routine or heavy-use shock, run Boost—24 hours of maximum generation. That’s what it’s for.
  • For an extra manual shock, use MPS or liquid chlorine, neither of which adds CYA. Hot Spring names both as approved.
  • Use dichlor only at start-up to build the first residual, shocking to 5 ppm no more than once a day, and stop adding it once the water holds 3 ppm.
  • Never use trichlor tablets, floating dispensers, calcium hypochlorite, or bromine with the salt system.
The Cyanuric Acid Rule

Dichlor is stabilized: every 1 ppm of chlorine it adds brings roughly 0.9 ppm of cyanuric acid along, and CYA never leaves a covered spa—it only accumulates. Hot Spring treats up to about 50 ppm as acceptable; past that, CYA binds free chlorine so the strip reads fine while the water goes bad (“chlorine lock”). The signs: you keep dosing dichlor and never get a lasting residual. When that happens, stop adding dichlor, test CYA, and plan a partial or full drain. Prevent it by using MPS, Renew, Boost, or liquid chlorine for routine shocking and saving dichlor for small maintenance doses on a chlorine spa. Our chlorine-demand guide covers the fix.

On a Bromine Spa

Bromine spas shock with MPS, not dichlor: the oxidizer reactivates the bromide bank into bromine and burns off bromamines, with no chlorine added. Use Renew or FreshWater MPS at the 2-oz-per-250-gallon rate (4 oz per 250 for Leisure Time’s Reserve & Renew program), and keep bromine at 1–3 ppm per the Leisure Time guide. Never mix bromine with a FreshWater Salt System.

Five Shock Mistakes

  • Shocking with the cover on. The chloramines you just broke apart redissolve. Cover off, 15–20 minutes.
  • Pouring granules into the filter compartment or skimmer. Concentrated dichlor bleaches filter media and can etch the shell. Broadcast it over moving water.
  • Getting in too soon. Above 5 ppm free chlorine irritates skin and eyes. Test first.
  • Shocking daily with dichlor. That’s the CYA trap. Once a day at start-up, then weekly at most—and MPS or Boost in between.
  • Shocking to fix a filter problem. Cloudy water from a loaded filter doesn’t clear with oxidizer. Pull and rinse the filter first; our cloudy-water guide explains why.

Frequently Asked Questions

How much shock do I put in my hot tub?

By the label: dichlor granules (FreshWater Chlorine Granules or Leisure Time Spa 56) at 1 oz per 500 gallons to shock, about 2 tablespoons, which is double the ½-oz routine dose; MPS non-chlorine shock (FreshWater MPS or Leisure Time Renew) at 2 oz per 250 gallons; or liquid chlorine at roughly ⅔ fl oz of 10–12% pool chlorine, or 1 fl oz of plain 6% bleach, per 100 gallons for about 5 ppm. Jets on, cover off, circulate 15–20 minutes, and test before soaking.

How long after shocking a hot tub can I get in?

When free chlorine reads 5 ppm or less—typically 15–30 minutes after a standard dichlor dose, and about 15 minutes of circulation after MPS non-chlorine shock. Always test with a strip rather than going by the clock; a heavy dose or a small spa takes longer to come down.

What’s the difference between chlorine shock and non-chlorine shock?

Dichlor chlorine shock both oxidizes organics and raises the sanitizer residual, but adds cyanuric acid with every dose. MPS non-chlorine shock (FreshWater MPS, Leisure Time Renew) oxidizes organics and frees existing chlorine or bromine to work without adding sanitizer or stabilizer, and you can soak again in about 15 minutes. Use dichlor when the residual is low; use MPS for routine weekly and after-use oxidizing, on bromine spas, and on salt systems.

Should I shock a salt water hot tub?

Yes, but with Boost or a non-stabilized shock. Run the FreshWater Salt System’s Boost mode for routine or heavy-use shocking; for a manual shock use MPS or liquid chlorine, which Hot Spring approves and which add no cyanuric acid. Use dichlor only at start-up to build the first residual, once a day at most, and stop once the water holds 3 ppm. Never use trichlor, floating dispensers, calcium hypochlorite, or bromine with a salt system.

Can I use bleach to shock my hot tub?

Yes—plain, unscented household bleach (5–6% sodium hypochlorite) or 10–12% liquid pool chlorine. Hot Spring lists both as approved, and they add no cyanuric acid. About 1 fl oz of 6% bleach or ⅔ fl oz of pool chlorine per 100 gallons raises chlorine roughly 5 ppm. Never use splashless, scented, or thickened bleach. Liquid chlorine raises pH, so retest and adjust afterward.

Do you ship hot tub shock?

Yes. Leisure Time Inc. ships FreshWater Chlorine Granules and MPS, Leisure Time Spa 56 and Renew, test strips, and other water care products throughout the contiguous United States, with free shipping on most orders over $99. Chlorine and MPS are hazmat-classified and can’t ship to Alaska, Hawaii, or U.S. territories. Orders ship from Idaho Falls, Idaho, typically within 3–7 business days.

The Right Shock for Your Spa, Measured Right

FreshWater Chlorine Granules and MPS, Leisure Time Spa 56 and Renew, and the test strips that tell you when you’re done—free shipping on most orders over $99, or on Autoship so the weekly shock is always on the shelf.

Shock is a dose with a purpose, and the purpose decides the product: dichlor when the residual is low, MPS or Renew for the weekly burn-off and after a crowd, liquid chlorine when you want a fast residual without stabilizer, and Boost on a salt spa. Take the label rate for your gallons, add it to moving water with the cover off, test in fifteen minutes, and get in when the strip says 5 or less. If your water won’t hold a residual no matter how much you shock, stop dosing and send your readings to hello@leisuretimeinc.com or call (208) 973-1384—that’s a different problem, and we’ll find it.

Dichlor 1 oz per 500, MPS 2 oz per 250, liquid chlorine ⅔ fl oz per 100—jets on, cover off, test before you soak. Everything ships to your door.


Tags: How Much Shock Hot Tub, Hot Tub Shock Dosage, Dichlor Dose, MPS Shock, Non-Chlorine Shock, Liquid Chlorine Hot Tub, Leisure Time Renew, FreshWater MPS, Spa 56, Hot Tub Chemicals, FreshWater, Leisure Time Spa Care