Holiday Shipping Notice: Orders placed after Nov. 24th will not be processed until Nov. 30th.


A Dealer’s Troubleshooting Guide—The Five Reasons Chlorine Disappears, How to Tell Which One Is Eating Yours, Why Repeated Dichlor Eventually Locks Up a Spa, the Salt-System Checks Nobody Mentions, and the Fix With FreshWater® or Leisure Time® Spa Care Products


If your hot tub won’t hold chlorine—you add it, it reads fine, and a day later it’s back to zero—one of five things is consuming it: a heavy organic load (new fill, a party, or chloramines that need breaking), phosphates feeding bacteria faster than the sanitizer can keep up, cyanuric acid that has built up from repeated dichlor until the chlorine can no longer work, biofilm in the plumbing re-seeding the water, or, on a FreshWater® Salt System spa, a setting or cartridge problem rather than a water problem. Each has a specific test and a specific fix, and this guide walks through them in the order we check them. Every product here—FreshWater® or Leisure Time® Spa Care—ships nationwide from our online store.

“It won’t hold chlorine” is the most frustrating water-care call we take, because the owner has usually done everything right and is now pouring in product that vanishes. The reason it vanishes is almost never that the chlorine is bad. Something is using it up, or something is stopping it from working. Find out which, and the fix is usually one product and one weekend. Keep guessing, and you’ll drain a spa you didn’t need to—or worse, keep one you did.

First: FreshWater or Leisure Time Spa Care?

Both lines fix chlorine demand, and we sell both. FreshWater® is made by Watkins Wellness for Hot Spring® and Caldera® spas, and it’s the line to use if you have the FreshWater Salt System or FreshWater IQ—and this is the one problem where the salt system itself needs checking, so there’s a dedicated section below. Leisure Time® Spa Care is a universal line for any spa brand and any sanitizer, and our recommendation for Sundance, Jacuzzi, Bullfrog, and most other spas. Every fix below gives you both. Browse the FreshWater collection and the Leisure Time Spa Care collection.

Find What’s Eating Your Chlorine

Dip a strip and work down the table. The clues on the left are what separates one cause from the next:

The Clue The Cause The Test The Fix
Fresh fill, a party, or a week of heavy use; strong chlorine smell; total chlorine well above free 1. Organic demand & chloramines Free vs. total chlorine on a 5-Way strip Shock to breakpoint; it usually holds after one or two
Shocked twice, still drops to zero within a day; water may be slightly hazy 2. Phosphates Phosphate test strip: over 300 ppb Clean the filter, dose phosphate remover, retest
Months of dichlor granules; chlorine reads fine but the water still clouds or smells; a salt spa that can’t keep up 3. Cyanuric acid (CYA) lockup CYA test: over 50–100 ppm in a spa Drain (partial or full); switch to a non-stabilized shock
Musty smell, slimy jets, flakes from the jets, foam that returns 4. Biofilm Pinch a flake—slimy; chlorine demand that never drops Purge the plumbing, drain, refill
FreshWater Salt System spa; chlorine bar in the red despite a normal Output Level 5. Salt-system settings or cartridge Cartridge age and electrodes; salt level; Output Level Boost, raise Output, clean or replace the cartridge
Cover left off in summer sun; water above 104°F UV and heat — Cover on; chlorine degrades fast in sunlight and very hot water

1. Organic Demand and Chloramines

Every bather adds sweat, oils, and lotions; a fresh fill brings its own organic load; and every bit of it consumes chlorine. Chlorine that has reacted with that load becomes chloramine—still measured as total chlorine, no longer working, and smelling like a pool. A spa with a big backlog can eat two or three normal doses before any free chlorine survives. This is the most common cause after a party or a refill, and the only one the fix for is simply more oxidizer, once, properly.

The Fix

Shock to breakpoint: a dose large enough to burn through the whole backlog at once, with the jets on and the cover off so the chloramines gas off instead of redissolving. Rinse the filter afterward. Retest the next day; if free chlorine holds, you’re done. If it doesn’t, move to cause 2.

Option A: FreshWater Option B: Leisure Time Spa Care
FreshWater 5-Way Test Strips  •  FreshWater MPS Chlorine-Free Oxidizer (shocks without adding stabilizer) or FreshWater Chlorine Granules  •  on a salt-system spa, Boost for 24 hours Leisure Time Renew non-chlorine shock (2 oz per 250 gallons; no stabilizer)  •  Leisure Time Spa 56 to restore the residual  •  Leisure Time Spa & Hot Tub Test Strips

2. Phosphates

Phosphates are plant food. They don’t consume chlorine directly; they feed the bacteria and algae that do, so the sanitizer is spent fighting growth you can’t see. The tell is a spa that has been shocked properly, is in balance, and still drops to zero within a day. Phosphates come in with fill water (some municipal systems add phosphate-based corrosion control), with dust and wildfire ash, and in some lotions and cleaners.

The Fix

  1. Test with a phosphate strip. The target is under 300 ppb; above that, treat.
  2. Clean the filter first—a fouled filter traps and re-releases phosphates and undermines the treatment.
  3. Dose phosphate remover per the label with the jets running. It binds the phosphates so the filter can capture them; expect the water to cloud for up to 24 hours, then clear.
  4. Rinse the filter and retest. Treat to the target, not to zero—over-dosing leaves a residual of its own that can foul a FreshWater IQ sensor.
  5. Shock once more and watch chlorine hold.
Option A: FreshWater Option B: Leisure Time Spa Care
FreshWater Phosphate Test Strips  •  FreshWater Phosphate Remover  •  FreshWater Filter Cleaner Leisure Time doesn’t make a phosphate remover, and that’s fine—FreshWater’s strips and remover work in any spa with any sanitizer. Use them, clean the filter with Leisure Time Filter Clean, then shock with Renew

3. Cyanuric Acid Lockup: The One That Reads Fine and Isn’t

This is the cause almost nobody tests for, and it’s the reason a spa can show 3 ppm on the strip and still smell, cloud, and grow things. Dichlor—the most common granular spa chlorine—is stabilized: every dose adds roughly 0.9 ppm of cyanuric acid (CYA) for every 1 ppm of chlorine. CYA is a sunscreen for chlorine; in a covered hot tub it isn’t needed, and unlike chlorine, it never leaves. It only accumulates. As CYA climbs, it binds more and more of the free chlorine into a form that reads on a strip but kills slowly or not at all. By the time CYA passes 100 ppm, 3 ppm of chlorine behaves like a fraction of that, and the spa “won’t hold” in the only sense that matters—it can’t keep the water sanitized.

How to Tell

Months of dichlor use; chlorine reads normal but water quality says otherwise; and a CYA test above 50–100 ppm. FreshWater and Leisure Time strips don’t read CYA; use a cyanuric acid test strip from our water-care collection, or bring a sample to any of our showrooms and we’ll test it free.

The Fix

There’s no chemical that removes CYA in a practical way; the fix is dilution. Drain a third to half the water for moderate levels, or drain fully for high ones, refill, and—this is the part that prevents a repeat—stop using dichlor as your routine shock. Sanitize with a system that doesn’t add stabilizer (a salt system, a mineral or @ease system) or keep dichlor doses small, and shock with a non-stabilized oxidizer: MPS, Renew, or liquid chlorine.

Option A: FreshWater Option B: Leisure Time Spa Care
A cyanuric acid test strip from our spa water care collection  •  FreshWater MPS Chlorine-Free Oxidizer as the routine shock going forward  •  on a FreshWater Salt System spa, the system generates unstabilized chlorine, so CYA only builds if you shock with dichlor—use Boost, MPS, or liquid chlorine instead  •  Clean Screen Pre-Filter and the Salt System Start-Up Kit for the refill Leisure Time Renew as the routine non-stabilized shock  •  Spa 56 in small maintenance doses only  •  Jet Clean before the drain, Metal Gon during the refill
Why We Say “Boost, Don’t Bucket” on Salt Spas

A FreshWater Salt System makes its own chlorine with no stabilizer at all, which is one of its quiet advantages—CYA never builds. The way owners undo that advantage is by shocking with dichlor granules every time the reading dips. Each scoop adds CYA the system can’t remove, and after a season the spa is locked up and needs a drain. When a salt spa needs a shock, run Boost; if you want a manual shock on top, use MPS or plain liquid chlorine. Save the dichlor for a chlorine spa, in small doses.

4. Biofilm

A bacterial film inside the plumbing constantly sheds bacteria into the water, and the sanitizer in the tub spends itself killing the new arrivals without ever reaching the source. The clues are the ones from our smelly-water and white-flakes guides: a musty or sour smell, a slick shell, soft flakes from the jets, foam that returns, and chlorine demand that stays high no matter what’s added. The fix is to clean the pipes: remove the filter, add a plumbing purge, run every jet on high for 20–30 minutes, drain, deep-clean or replace the filter, refill through a pre-filter, and shock. Then purge at every future drain so it never re-establishes.

Option A: FreshWater Option B: Leisure Time Spa Care
A plumbing purge from our spa water care collection (Leisure Time Jet Clean works in any spa, salt systems included)  •  FreshWater Spa Vac  •  FreshWater Filter Cleaner  •  Clean Screen Pre-Filter Leisure Time Jet Clean (remove the filter first)  •  Leisure Time Filter Clean  •  Renew to shock the fresh water  •  Enzyme weekly after

5. On a FreshWater Salt System Spa: Check the System Before the Water

A salt system that “won’t hold chlorine” is often a system that isn’t making enough, and that has its own short checklist. Work through it before draining anything:

  1. Run Boost. Twenty-four hours of maximum generation clears most backlogs on its own. Hot Spring’s guidance after heavy use is simply: Boost, then retest.
  2. Check the Output Level. Levels 1–10 set how many hours a day the cartridge generates. A level that was right for two people in April isn’t right for six in July; raise it one step and retest in a few days. Use the 10-day reminder to confirm.
  3. Check the cartridge’s age. Cartridges last about four months (the panel counts it down). An expired cartridge generates less and then nothing. Replace it.
  4. Pull the cartridge and look at the electrodes. A white coating is calcium scale, and a scaled cartridge can’t generate. Soak it in a pH-down solution (about three tablespoons in twelve ounces of water) or diluted vinegar until the bubbling stops, rinse, reinstall, and Boost—then get hardness toward 50 ppm so it doesn’t scale again.
  5. Check the salt level. Target about 1,750 ppm. Below range, the system can’t generate; splash-out and top-offs dilute it over time. Add FreshWater Spa Salt per the panel’s prompt.
  6. Check phosphates and metals. High phosphates consume what the system makes; metals in the water coat the electrodes. Treat per causes 2 and the fill-water guide.
  7. Check CYA if the spa has ever been shocked with dichlor; see cause 3.
FreshWater Salt System Essentials
Salt System Maintenance Bundle (replacement cartridge, 10 lb spa salt, test strips)  •  FreshWater Salt Test Strips and Spa Salt in the FreshWater collection  •  pH/Alkalinity Down for the cartridge soak  •  Vanishing Act to fix hardness  •  put the cartridge on Autoship every four months so it’s never expired

Our Salt System explainer and FreshWater IQ explainer cover every setting. If you have IQ, its hourly chlorine reading and plain-language instructions will usually name the problem for you.

What to Do Tonight, in Order

  1. Test free and total chlorine, pH, and alkalinity. Fix pH to 7.2–7.8 first; chlorine works poorly above 7.8 and the reading can mislead.
  2. Shock to breakpoint—MPS, Renew, or Boost—cover off, jets on 20 minutes. Rinse the filter.
  3. Salt spa? Check cartridge age, electrodes, salt level, and Output Level while the Boost runs.
  4. Tomorrow: retest. Holding? You’re done—it was organic demand. Back to zero?
  5. Test phosphates. Over 300 ppb: clean the filter, dose remover, retest in 24 hours, shock again.
  6. Still dropping with phosphates in range? Smell and feel the water. Musty and slimy: biofilm—purge and drain. Months of dichlor: test CYA—if high, drain.
  7. Refill the right way: pre-filter, treat metals and hardness, balance, shock with a non-stabilized oxidizer, and set the routine below.

Keeping Chlorine Where It Belongs

  • Shock weekly with a non-stabilized oxidizer—MPS, Renew, or Boost—and after any heavy-use soak. Keep dichlor for small maintenance doses on chlorine spas, or skip it entirely on a salt spa.
  • Test phosphates at every fill and after dust or smoke events; treat to 300 ppb, not to zero.
  • Test two to three times a week and hold 3–5 ppm; gaps are where demand and biofilm start.
  • Rinse before you soak and keep spa-only suits; less organic load means less chlorine spent.
  • Keep the cover on when the spa isn’t in use; sunlight destroys unstabilized chlorine fast.
  • Purge the plumbing at every drain and refill through a pre-filter with metals and hardness treated.
  • On a salt spa: replace the cartridge every four months, inspect it for scale at each change, confirm salt at the 10-day reminder, and adjust the Output Level with the seasons.
  • Autoship the strips, shock, phosphate remover, and salt cartridge so the routine never lapses: Autoship.
Before You Drain, Rule Out the Cheap Fixes

A drain and refill costs water, chemicals, a weekend, and—on hard Idaho water—another round of hardness treatment. Three of the five causes here are fixed without one: organic demand (a shock), phosphates (a bottle of remover), and a salt system’s settings or cartridge (a Boost, a soak, or a replacement). Work the list in order and drain only for CYA lockup or biofilm, where dilution or a purge is the only real answer. If you’re stuck between them, bring us a sample—we test chlorine, CYA, phosphates, and metals free at all three showrooms.

Frequently Asked Questions

Why won’t my hot tub hold chlorine?

Something is consuming it or stopping it from working: a heavy organic load and chloramines (fix with a breakpoint shock), phosphates feeding bacteria (test and treat to under 300 ppb), cyanuric acid built up from repeated dichlor (drain and switch to a non-stabilized shock), biofilm in the plumbing (purge and drain), or—on a FreshWater Salt System spa—an expired or scaled cartridge, low salt, or an Output Level set too low. Work through them in that order.

Can phosphates cause high chlorine demand in a hot tub?

Yes. Phosphates don’t consume chlorine directly; they feed the bacteria and algae that do, so a spa with high phosphates burns through sanitizer no matter how much is added. Test with a phosphate strip; above 300 ppb, clean the filter, dose FreshWater Phosphate Remover with the jets running, let the water clear over 24 hours, rinse the filter, and retest. Treat to the target, not to zero.

What is cyanuric acid and why does it matter in a hot tub?

Cyanuric acid (CYA) is the stabilizer in dichlor chlorine granules—about 0.9 ppm of CYA for every 1 ppm of chlorine added. It protects chlorine from sunlight, which a covered hot tub doesn’t need, and it never leaves the water. As it accumulates past 50–100 ppm, it binds free chlorine so the strip reads fine but the chlorine barely works. The only fix is dilution: drain partially or fully, and shock with a non-stabilized oxidizer such as MPS, Renew, or liquid chlorine from then on.

Why is my FreshWater Salt System not holding chlorine?

Check the system before the water: run Boost; raise the Output Level a step if use has increased; replace the cartridge if it’s past its four-month life; pull it and soak the electrodes in a pH-down solution if they’re white with scale; confirm salt is near 1,750 ppm; and test phosphates and metals. Avoid shocking a salt spa with dichlor—it adds cyanuric acid the system can’t remove. Use Boost, MPS, or liquid chlorine instead.

Should I use FreshWater or Leisure Time products when chlorine won’t hold?

Both work. FreshWater is the line for Hot Spring and Caldera spas, especially with the FreshWater Salt System or FreshWater IQ, and its phosphate strips and remover work in any spa. Leisure Time Spa Care is a universal line for any spa and sanitizer; Renew is a non-stabilized shock that won’t build cyanuric acid, and Jet Clean is the best biofilm purge we carry. We stock and ship both.

Do you ship hot tub shock, phosphate remover, and salt cartridges?

Yes. Leisure Time Inc. ships FreshWater, Leisure Time Spa Care, and other water care products, salt cartridges, filters, and accessories throughout the contiguous United States, with free shipping on most orders over $99 and flat rates on heavier items. Some hazmat-classified chemicals can’t ship to Alaska, Hawaii, or U.S. territories. Orders ship from Idaho Falls, Idaho, typically within 3–7 business days.

Find What’s Eating Your Chlorine—Then Fix That

Phosphate strips and remover, MPS or Renew for a stabilizer-free shock, salt cartridges and spa salt, Jet Clean for biofilm—free shipping on most orders over $99, or on Autoship so the cartridge is never expired and the routine never lapses.

A spa that won’t hold chlorine isn’t a mystery; it’s a short list. Shock properly once and see if it holds. If not, test phosphates. If those are fine, smell for biofilm and test for cyanuric acid. On a salt spa, check the system first. Three of the five fixes cost a bottle and an evening; the other two cost a drain, and now you’ll know when one is worth it. If you’d rather have a second set of eyes, send your readings to hello@leisuretimeinc.com or call (208) 973-1384—our water-care team chases down chlorine demand for every brand of spa, every day.

Shock, then phosphates, then CYA or biofilm, then the salt system—work the list in order and the chlorine stays. Everything you need ships to your door.


Tags: Hot Tub Won't Hold Chlorine, Chlorine Demand, Phosphates Hot Tub, Cyanuric Acid Hot Tub, CYA Lockup, FreshWater Salt System, Boost, Hot Tub Shock, Hot Tub Troubleshooting, FreshWater, Leisure Time Spa Care